Ejection System Optimization for Ejector Pin Mark and Stress Whitening Defects
Ejection System Optimization for Ejector Pin Mark and Stress Whitening Defects Ejector pin mark and stress whitening are typical ejection defects. Both appear at the contact position between ejector pin and plastic parts. Ejector pin marks show as dents, bright spots or raised traces. Stress whitening is material whitening caused by tensile stress, sometimes accompanied by microcracks. Many on-site operators only slow down ejection speed and reduce ejection force for temporary improvement, without solving root causes from ejection system structure. The defects recur repeatedly and bring high reject rate for appearance parts, transparent parts and high-toughness plastic products. The core of ejection optimization is reducing demolding resistance, dispersing ejection pressure, guaranteeing synchronous ejection and eliminating vacuum adsorption, so as to reduce local stress concentration from structural design.
Optimization of Ejector Pin Layout and Specification
Ejector pin arrangement should match the wrapping force distribution instead of simple uniform layout. Pins are arranged at screw bosses, ribs and thick wall areas with high structural strength, avoiding appearance surface and center of thin flat plates. Single-point ejection in the middle of flat plate easily causes annular whitening because the area lacks enough support and plastic is stretched under concentrated pressure. Large-diameter ejector pins are preferred when space allows, increasing contact area and lowering unit pressure. Under same ejection force, larger pin diameter greatly reduces whitening risk. Flat ejector pins are used for narrow rib space, and sleeve ejectors for boss columns. Sleeve ejectors have annular contact surface and uniform stress, better than thin single pins for avoiding whitening. If ejector points have to be set on appearance backside, blade ejectors and ejector blocks are adopted to replace point contact and weaken traces. Local thickening design of 0.05mm to 0.2mm is reserved on the back of parts to limit ejection stress in thickened area and protect the appearance surface.

Ejection Balance and Ejector Plate Improvement
Deformed ejector plate and excessive guide gap lead to asynchronous ejection. Bent ejector plate causes partial pins to touch the product in advance and form local whitening. Support columns are added in the middle of ejector plate and reset springs are installed at four corners to reduce suspended area and keep plate flat during ejection. The fitting clearance of ejector pins, sleeves and angle lifters is controlled uniformly. Too small clearance causes sticking and inconsistent ejection resistance, while too large clearance leads to flash. Long-stroke deep cavity molds need extra ejection guide pins to prevent plate offset. Complex products can adopt two-stage ejection structure. Pre-demolding is carried out first to separate the part from core, then main ejection is executed to split concentrated ejection force and reduce instantaneous stress.
Vacuum Adsorption and Auxiliary Air Inlet Design
Vacuum negative pressure forms between core and inner surface of deep shell and thin-wall container during demolding, which brings extra huge demolding resistance. Even with reasonable pin layout, stable whitening still occurs. It is hard to solve this problem only by adjusting molding parameters. Auxiliary air inlet structure inside cores is required to feed low-pressure clean air synchronously with ejection and break vacuum. Air grooves can be processed on the outer wall of ejector pins with shallow 0.02mm to 0.05mm exhaust slots, or independent air inlet inserts are set on core inserts. Air channels avoid sealing positions to prevent flash during production. Air inlet structure works well on daily chemical bottles, medical sampling tubes and deep shell molds, greatly reducing friction and pulling whitening.
Matching Optimization of Demolding Resistance
Ejection performance is closely related to draft angle and cavity surface texture. Insufficient draft angle for smooth surface or inadequate angle for textured surface increases side wall friction and required ejection force. PC and PC/ABS sensitive to demolding stress need at least 1.5-degree draft angle for smooth surface, and extra 0.5 to 1 degree for textured surface. Uniform cavity polishing reduces micro friction. Poorly polished core surface scratches the inner wall during demolding and worsens whitening together with ejection pressure. The head of ejector pins must be flat with small rounded corners at edges. Sharp edges easily cut plastic and trigger stress concentration.

Alternative Ejection Schemes
Push plate ejection is the priority for high appearance parts that cannot accept pin marks. Push plate releases parts by whole circle surface contact without point traces, with uniform force. It is suitable for flat and shallow high-gloss parts, with higher machining and fitting difficulty and mold cost. Angle lifters and side core pulling are finished before ejection for areas with strong wrapping force, avoiding simultaneous pulling from angle lifters and ejector pins. Adding ejector blocks to replace partial thin pins is a low-cost improvement scheme for mold modification on existing molds.
Molding Process and Trial Verification
Structural optimization needs matching molding parameters. Insufficient cooling makes soft parts easy to be pressed with marks. Enough cooling time is required to guarantee rigidity before ejection. Ejection curve adopts slow start and uniform advancing to avoid instant impact. Material toughness and shrinkage affect whitening performance. POM, PC and transparent PS are sensitive to stress, so larger safety margin should be reserved in mold design. Continuous sampling is needed after mold modification to observe appearance changes under different ejection speed and mold temperature, and stable parameters are fixed. Regular inspection of pin wear and fitting gap is required, because worn pins will aggravate mark defects. The improvement of ejector pin marks and whitening is a combined solution, instead of simply replacing ejector pins. Engineers should check vacuum adsorption, asynchronous ejection and insufficient draft angle first, then adjust ejection structure and pin layout to control stress within material tolerance and meet quality standard of appearance parts.
