How to Select Mold Steel: Comparison Guide of P20, 718H, NAK80 and S136
How to Select Mold Steel: Comparison Guide of P20, 718H, NAK80 and S136 Plastic mold steel selection directly decides mold service life, surface forming effect, polishing performance and long-term maintenance cost. Improper steel selection in early project stage will lead to unqualified polishing, rust and fast wear during mass production. P20, 718H, NAK80 and S136 are four widely used pre-hardened and stainless steel grades in injection industry. Their applicable scenarios differ greatly. Engineers should balance appearance requirement, production volume, material property and budget to select suitable steel.
Basic Characteristics and Application of P20 Mold Steel
P20 is common pre-hardened plastic mold steel with delivery hardness from 28HRC to 32HRC. No extra heat treatment is needed. It can be processed directly after roughing with good cutting performance, low processing resistance and short machining cycle. Its procurement cost is the lowest among these four grades. Its polishing capacity is limited, only suitable for ordinary finish. Texture etching performance is average. Corrosion resistance is weak. It is easy to get rust and pitting in humid environment or when molding corrosive plastic. It fits small and medium batch structural parts, internal brackets and turnover accessories with simple matte or sandblasted surface. The mold service life is generally within 100,000 shots. It is not suitable for long continuous mass production, PVC or flame-retardant plastics which release corrosive gas.

Basic Characteristics and Application of 718H Mold Steel
718H is modified pre-hardened steel with delivery hardness from 33HRC to 38HRC. Heat treatment is not required. Its metallographic structure is uniform. Compared with P20, it has better polishing, etching uniformity and stable hardness. Machining difficulty is slightly higher. It can reach fine polishing effect and adapt to most matte and fine sand textures. Etching is less likely to show uneven pattern and color difference. It has good toughness and is not easy to crack at sharp corners and deep ribs on large molds. 718H is the mainstream steel for home appliance and automotive interior and exterior parts. It fits medium batch production with service life of 200,000 to 300,000 shots for matte appearance shells and structural parts. Its rust resistance is still poor. Rust prevention work must be done during shutdown when molding flame-retardant or acidic precipitating plastics. It is not suitable for high-gloss and transparent products.
Basic Characteristics and Application of NAK80 Mold Steel
NAK80 is high-hardness pre-hardened steel with stable delivery hardness around 40HRC without quenching. It has excellent polishing performance and can reach mirror finish. Texture etching is delicate and uniform. Polishing recovery after EDM is fast with few residual processing marks. The steel has high purity and stable hardness distribution without local deviation. It is widely used for cosmetic shells, daily chemical caps, high-gloss panels and small precision appearance parts. Its service life is about 300,000 to 400,000 shots. However, its corrosion resistance is still weak and cannot sustain long-term production of corrosive materials. Its price is higher than 718H. High hardness slows down processing speed and increases tool loss. It is not recommended for extra large thick plate molds due to processing stress risk.
Basic Characteristics and Application of S136 Mold Steel
S136 belongs to martensitic stainless mold steel, different from the above three pre-hardened grades. It is normally supplied in annealed state. Quenching and tempering are required after machining, reaching hardness of 48HRC to 52HRC. It has outstanding rust and corrosion resistance. Its polishing ceiling is the highest, suitable for transparent parts, optical components and high-gloss non-spray products. It can resist corrosion when molding PVC, flame-retardant PC and acidic plastics. Its service life can exceed 500,000 shots for long stable mass production. Its disadvantages are obvious. Heat treatment will bring tiny deformation, so deformation allowance must be reserved in mold design. It has high machining difficulty and strict requirements on heat treatment factory. Its raw material and processing cost are the highest of four grades.

Selection Judgment Logic
Appearance requirement is the first consideration. P20 is preferred for simple matte sandblasted surface, limited budget and small batch. 718H is the cost-effective choice for medium appearance, fine etching and stable medium batch. NAK80 is selected for high-gloss mirror small precision appearance parts without heat treatment. S136 is adopted for transparent optical parts, corrosive raw materials and long-term large-batch production. Raw material and workshop environment also matter. If the workshop is humid or the plastic contains flame retardant, S136 is recommended to reduce rust and polishing rework cost. Invisible structural parts do not need high-cost mirror steel to control mold budget.
Common Misunderstandings in Steel Selection
Higher hardness does not mean better performance. NAK80 has high hardness but poor rust resistance, so it will still corrode when processing flame-retardant materials. S136 is anti-rust but has heat treatment deformation risk. Thin-wall precision parts need deformation evaluation in advance. Many engineers choose NAK80 for mirror parts and ignore material corrosion risk. Cavity surface will form foggy spots after long production, bringing high repair cost. Different versions of 718 have different purity. High-purity grade is required for strict etching projects. Reasonable steel matching is not blindly choosing expensive grades. It balances appearance, output, raw material and budget to reduce surface defects during trial and mass production, and cut maintenance and polishing repair cost.
