China Investigation of Burning and Short Shot Defects Caused by Poor Mold Venting
During injection molding, trapped air inside the mold cavity is a major trigger for burning and short shot defects. Many on-site technicians tend to adjust injection speed, pressure and melt temperature first. Repeated modification of process parameters often fails to solve the root cause, because they cannot distinguish the defect characteristics brought by poor venting or follow a standardized inspection sequence. Burning and short shot often appear together, yet they differ in appearance, occurrence position and corrective actions. It is necessary to verify one by one combined with product structure, mold vent layout and molding process.
1. Identification of defect features
Burning caused by poor venting usually occurs at the end of melt flow, the top of thin ribs, sharp corners, thin-wall distal areas and weld lines. The burnt area turns dark black, the surface plastic undergoes thermal decomposition, and the edge is often brittle and peeling. Different from burning caused by overheated barrel or degraded raw material, venting-related burning appears at fixed positions in every trial run. Reducing injection speed can relieve burning, yet short shot may occur at the same time. Short shot from trapped air mostly happens at the terminal of melt flow. Compressed air creates back pressure to block melt advancement, resulting in incomplete filling. The fracture surface of the unfilled section is relatively clean without obvious burn marks. Raising injection pressure hardly fills the cavity, and excessive pressure will turn the defect into burning. If short shot appears near the gate or at the root of ribs, it is generally not a venting issue. Prior checks should focus on runner and gate size as well as material fluidity.

2. Basic inspection of mold venting system
Check the status of existing vent grooves first. Vent grooves are easily blocked by plastic residue, color powder and release agent, especially for multi-cavity molds, where blockage in individual cavities leads to uneven defect rates. When cleaning vents, confirm the depth matches the raw material requirement. For common ABS and PC/ABS, vent depth is controlled between 0.015mm and 0.02mm. Low-viscosity materials such as PP and PE can use slightly deeper vents, while engineering plastics like PC and PBT need shallower vents. Over-deep vents will produce flash, and shallow vents cannot exhaust air effectively. The vent channel must extend to the outer parting surface instead of forming a closed groove. Apart from parting surface vents, check vents on inserts, slides, lifters and ejector pins. Deep ribs and deep bosses cannot rely only on parting surface vents, and air tends to accumulate at rib tops, where vents on inserts or ejector pins are required.
3. Verification of product structure and weld line positions
Product structure determines air trapping zones. Long thin ribs, closed ring structures, thin-wall ends and weld lines formed by converging melt flows are high-risk positions for trapped air. Mold flow analysis can visually display air gathering areas and reserve vents in the design stage. For finished molds, check the melt flow path against defect locations. For multi-gate molds, air is easily wrapped when two melt streams converge. If burning or short shot occurs at weld lines, poor venting is the primary cause. Some undercut structures have tightly sealed slide surfaces without reserved air channels, and defects stably appear at undercut positions when melt fills this area.
4. Auxiliary verification and adjustment of process parameters
Process adjustment is used to verify whether defects come from poor venting rather than serve as a permanent solution. Lower injection speed to slow down melt advancement and leave time for air discharge. If burning and short shot are improved, venting problems are confirmed. If defects remain unchanged after speed reduction, check raw material drying, barrel temperature, mold temperature and gate size instead. Segmented injection is a common debugging method, reducing speed near trapped air zones to avoid air encapsulation. Excessive back pressure and high barrel temperature accelerate plastic thermal decomposition and worsen burning under poor vent conditions. Raw material drying status also needs confirmation, as excess moisture will generate water vapor and form similar burn defects. Do not continuously increase injection pressure to force filling. High pressure compresses trapped air and raises temperature through adiabatic compression, aggravating burning and bringing flash and mold deformation risks.

5. Implementation of corrective actions
Cleaning blocked vent grooves is the first step. Establish regular vent cleaning inspection standards for mass production to prevent residue accumulation. Add new vent grooves on parting surfaces, inserts, lifters and ejector pins for insufficient vent positions. Breathable steel inserts can be adopted for deep ribs and deep screw bosses where it is difficult to machine vents, and regular maintenance is required to avoid pore blockage. Adjust gate positions or add extra gates to change melt flow direction and disperse air accumulation. For annular enclosed structures, overflow grooves can be added at product ends to carry trapped air and a small amount of melt, and the overflow material will be cut off as scrap later. Local vent gaps can be made on slide sealing surfaces to keep sealing performance while reserving air channels. After modification, restore process parameters gradually to verify stability and record defect changes for mold rectification files.
6. Continuous control during mass production
Mold venting performance declines with long-term production, as vent grooves are gradually filled by plastic debris and defects recur periodically. Add vent inspection items to mold maintenance checklists, and disassemble slides and inserts regularly for residue cleaning. When switching raw materials, color masterbatch or modifying formulas, material fluidity changes and vent layout needs re-evaluation. If product structure is revised and melt flow path changes, the original qualified vent system may fail, and air trapping verification must be carried out after modification. The troubleshooting sequence for burning and short shot caused by poor venting follows defect identification, vent groove inspection, melt flow path confirmation, process verification and structural rectification. Opening air discharge channels is the priority instead of relying only on process adjustment, so as to achieve stable molding yield.
